Enum gapi_grpc::google::cloud::dialogflow::v2::AudioEncoding

#[repr(i32)]pub enum AudioEncoding {
    Unspecified,
    Linear16,
    Flac,
    Mulaw,
    Amr,
    AmrWb,
    OggOpus,
    SpeexWithHeaderByte,
}

Audio encoding of the audio content sent in the conversational query request. Refer to the Cloud Speech API documentation for more details.

Variants

Unspecified

Not specified.

Linear16

Uncompressed 16-bit signed little-endian samples (Linear PCM).

Flac

FLAC (Free Lossless Audio Codec) is the recommended encoding because it is lossless (therefore recognition is not compromised) and requires only about half the bandwidth of LINEAR16. FLAC stream encoding supports 16-bit and 24-bit samples, however, not all fields in STREAMINFO are supported.

Mulaw

8-bit samples that compand 14-bit audio samples using G.711 PCMU/mu-law.

Amr

Adaptive Multi-Rate Narrowband codec. sample_rate_hertz must be 8000.

AmrWb

Adaptive Multi-Rate Wideband codec. sample_rate_hertz must be 16000.

OggOpus

Opus encoded audio frames in Ogg container (OggOpus). sample_rate_hertz must be 16000.

SpeexWithHeaderByte

Although the use of lossy encodings is not recommended, if a very low bitrate encoding is required, OGG_OPUS is highly preferred over Speex encoding. The Speex encoding supported by Dialogflow API has a header byte in each block, as in MIME type audio/x-speex-with-header-byte. It is a variant of the RTP Speex encoding defined in RFC 5574. The stream is a sequence of blocks, one block per RTP packet. Each block starts with a byte containing the length of the block, in bytes, followed by one or more frames of Speex data, padded to an integral number of bytes (octets) as specified in RFC 5574. In other words, each RTP header is replaced with a single byte containing the block length. Only Speex wideband is supported. sample_rate_hertz must be 16000.

Implementations

impl AudioEncoding

pub fn is_valid(value: i32) -> bool

Returns true if value is a variant of AudioEncoding.

pub fn from_i32(value: i32) -> Option<AudioEncoding>

Converts an i32 to a AudioEncoding, or None if value is not a valid variant.

Trait Implementations

impl Clone for AudioEncoding

fn clone(&self) -> AudioEncoding

Returns a copy of the value.

pub fn clone_from(&mut self, source: &Self)

Performs copy-assignment from source.

impl Copy for AudioEncoding

impl Debug for AudioEncoding

fn fmt(&self, f: &mut Formatter<'_>) -> Result

Formats the value using the given formatter.

impl Default for AudioEncoding

fn default() -> AudioEncoding

Returns the “default value” for a type.

impl Eq for AudioEncoding

impl From<AudioEncoding> for i32

fn from(value: AudioEncoding) -> i32

Performs the conversion.

impl Hash for AudioEncoding

fn hash<__H: Hasher>(&self, state: &mut __H)

Feeds this value into the given Hasher.

pub fn hash_slice<H>(data: &[Self], state: &mut H) where
    H: Hasher, 

Feeds a slice of this type into the given Hasher.

impl Ord for AudioEncoding

fn cmp(&self, other: &AudioEncoding) -> Ordering

This method returns an Ordering between self and other.

#[must_use]pub fn max(self, other: Self) -> Self

Compares and returns the maximum of two values.

#[must_use]pub fn min(self, other: Self) -> Self

Compares and returns the minimum of two values.

#[must_use]pub fn clamp(self, min: Self, max: Self) -> Self

Restrict a value to a certain interval.

impl PartialEq<AudioEncoding> for AudioEncoding

fn eq(&self, other: &AudioEncoding) -> bool

This method tests for self and other values to be equal, and is used by ==.

#[must_use]pub fn ne(&self, other: &Rhs) -> bool

This method tests for !=.

impl PartialOrd<AudioEncoding> for AudioEncoding

fn partial_cmp(&self, other: &AudioEncoding) -> Option<Ordering>

This method returns an ordering between self and other values if one exists.

#[must_use]pub fn lt(&self, other: &Rhs) -> bool

This method tests less than (for self and other) and is used by the < operator.

#[must_use]pub fn le(&self, other: &Rhs) -> bool

This method tests less than or equal to (for self and other) and is used by the <= operator.

#[must_use]pub fn gt(&self, other: &Rhs) -> bool

This method tests greater than (for self and other) and is used by the > operator.

#[must_use]pub fn ge(&self, other: &Rhs) -> bool

This method tests greater than or equal to (for self and other) and is used by the >= operator.

impl StructuralEq for AudioEncoding

impl StructuralPartialEq for AudioEncoding